SCREW COMPRESSORS SPECIALIST | Customer Satisfaction Is Our Goal | SCS is a member of ISNETWORLD for Safety Audit
* In Shop Overhaul *Machine Shop In House *Cast Iron Housing Repair *Balancing *Industrial Hard Chrome Rotor and Seal Journal *Industrial Hard Chrome Piston Rod *Laser Alignment *Fast Turn Around Time *OEM Parts *Fast Respond *OEM Paint or Customer Specification *Emergency 24-7 Service *New Compressors *Preventive Maintenance Vibration Analysis Oil Analysis *Remanufactured Compressors *Exchange Program

 

Frick TDSH Compressor Service Repair and Overhaul

 

 

ORDER FRICK PARTS

 

FRICK INSPECTION

 

FRICK OVERHAUL

 

FRICK SERVICE

 

FRICK GALLERY

The TDSH series, is used in typical refrigeration and natural gas applications up to 400 psig (27.6 bar). It is also offered with optional nodular iron pressure retaining housings up to 600 psig (41.4 bar). The PDSH series, with cast steel housings, is used in gas processing or industrial refrigeration in chemical and petrochemical applications up to 600 psig (41.4 bar). The compressors are direct drive at speeds from 600 to 4500 rpm for rotor sizes up to 9.173 in. (233 mm) or 600 to 3600 rpm for larger sizes. Power ratings of the series range from 250 to 6000 hp (186 to 4474 kW).

Frick compressors use 100% anti-friction bearings. Cylindrical roller bearings handle radial loads, and angular contact bearings, aided by a balance piston, absorb thrust loads. Roller bearings maintain accurate rotor positioning to minimize internal leakage and inefficiency. Frick TDSH, GDSH, RWB ii, RWF, RDB, SGC, SGCH, and SGCB bare screw compressors are designed to compress a variety of gases for quality solutions in refrigeration, water chilling, wellhead compression, gas gathering, and vapor recovery. The antifriction bearings minimize frictional power losses. Injected oil to lubricate the bearings, balance piston, seal and fill any leakage paths between and around the rotors to prevent internal gas recirculation losses. Oil injection also minimizes noise and vibration, keeping the compressor cool by absorbing much of the heat from compression. System differential pressure is normally sufficient for supplying oil to the bearings.

The Frick Rotary Screw Compressor features advanced technology and inherent reliability in its simplicity. Fewer moving parts and simple rotary motion means less maintenance, lower noise and vibration levels, and of course, lower total repair costs, saving you money time and time again. Compressor housings are machined to provide static oil reservoirs for the bearings. Therefore, Frick compressors can run in most applications without an oil pump. A steeples hydraulic or manually actuated slide valve moves axially along the rotor mesh line to provide unloading. Unloaded gas is internally bypassed back to suction before compression has begun, allowing the compressor to efficiently accommodate system requirements. A hydraulically actuated slide stop adjusts slide valve length to optimize internal discharge pressure. This matches compressor volume ratio (Vi) to system pressure ratio and eliminates the power penalties associated with typical screw compressor under- or over-compression. Vi is infinitely variable from 5.0 to 2.2 and also 3.0 to 1.7 on some models.

With 38 models ranging from 71 CFM to 5067 CFM, our gas compressors are available for almost every industrial refrigeration need

TDSH Series
TDSH 163L (RWBII76)
TDSH193S (RWBII100)
TDSH193L (RWBII134)
TDSH233S (RWBII177)
TDSH233L (RWBII222)

GDSH Series
GDSH163L (RWBII76)
GDSH193S (RWBII100)
GDSH193L (RWBII134)

* Cost effective solution for Frick compressor failure.
* Minimum production down time.
* Quick compressor swap and start up within 1-2 days.
* Warranty 1 year after start up.
* In stock Frick remanufactured compressors

FREE SCREW COMPRESSOR INSPECTION

Let us determine the extent of your problem, give you a full report, and best plan of action to get your compressor up and running as soon as possible. SCS does offer 24/7 around the clock repairs to eliminate your downtime. In some case you could be eligible for SCS exchange program offering a very quick turnaround. SCS Screw Compressors Specialist offers free screw compressor inspections for the following brands:

Trusted Compressor Overhaul and Rebuild Company. SCS Screw Compressor Repair has been servicing Screw Compressors for more than 30 years. Started working with RECO in 1985, Previous Owner Operator of RCS Refrigeration Components Service and Currently Own and operate SCS Screw Compressors Specialist.

IN SHOP OVERHAUL

SCS shop is equipped with all necessary tools and equipments - crane, forklift, special tool, etc. SCS tear down table has a building oil rail drain to catch all oil drain from compressor during disassembly so there is no oil on the floor that may cause slip and fall. PPE is always available for everyone. Safety training are done year round – safety certifications is required to work in the job site.

Hotshot Pickup & Delivery Services

24/7 Nationwide Hotshot Delivery Service to and from the location of the compressor needing repair.